This write up will show you how to set base ignition timing using an adjustable timing light. This applies to all 1G 4G63 engines INCLUDING non turboed 4G63's, as well as the 97-99 4G63 DSM's. The 95-96 4G63 DSM's DO NOT use a cam angle sensor (CAS) which will not allow you to adjust the base timing.
Tools Needed:
*3/8" drive ratchet
*12mm socket, 3/8" drive
*3" extension for a 3/8" drive
*Flat head screwdriver
*Adjustable Timing Light
Step 1: First, start your car and let it run for approximately 5 minutes or till the engine is at normal operating temperature. Turn off ALL accessories (A/C, heater, lights, radio, etc.)
Step 2: Remove the upper timing belt cover that protects the cam gears (if you have an upper timing belt cover).
Step 3: You will need to ground the ignition timing plug located on the firewall. This will override the ECU and make the car idle at 800RPMS.
Step 4: Hook up your timing light power leads to the battery terminals. Red to positive. Black to ground. Then, hook the timing light pickup to the number 1 spark plug wire (spark plug wire on the driver side/timing belt side end).
Step 5: Unbolt the CAS. There are (2) 12mm nuts that hold the CAS in place. Loosen these until you can rotate the CAS. Note- you DO NOT want to remove the nuts, just loosen them a bit. Only one nut is visible in the picture below.
Step 6: Set your adjustable timing light to 5* advanced. Start the engine, then point the timing light at the cam gears.
Step 7: Turn the CAS until the timing marks on the cam gears line up perfectly.
Step 8: Tighten the nuts back up on your CAS.
Step 9: Check your timing again to make sure the CAS did not rotate when you tightened it up.
Step 10: Un-ground the timing plug on the firewall.
And you're done! That was easy right?
Tools Needed:
*3/8" drive ratchet
*12mm socket, 3/8" drive
*3" extension for a 3/8" drive
*Flat head screwdriver
*Adjustable Timing Light
Step 1: First, start your car and let it run for approximately 5 minutes or till the engine is at normal operating temperature. Turn off ALL accessories (A/C, heater, lights, radio, etc.)
Step 2: Remove the upper timing belt cover that protects the cam gears (if you have an upper timing belt cover).
Step 3: You will need to ground the ignition timing plug located on the firewall. This will override the ECU and make the car idle at 800RPMS.
Step 4: Hook up your timing light power leads to the battery terminals. Red to positive. Black to ground. Then, hook the timing light pickup to the number 1 spark plug wire (spark plug wire on the driver side/timing belt side end).
Step 5: Unbolt the CAS. There are (2) 12mm nuts that hold the CAS in place. Loosen these until you can rotate the CAS. Note- you DO NOT want to remove the nuts, just loosen them a bit. Only one nut is visible in the picture below.
Step 6: Set your adjustable timing light to 5* advanced. Start the engine, then point the timing light at the cam gears.
Step 7: Turn the CAS until the timing marks on the cam gears line up perfectly.
Step 8: Tighten the nuts back up on your CAS.
Step 9: Check your timing again to make sure the CAS did not rotate when you tightened it up.
Step 10: Un-ground the timing plug on the firewall.
And you're done! That was easy right?
Fri Oct 30, 2015 9:31 pm by AJracer33a
» Project Onyx
Wed Oct 21, 2015 8:46 pm by Onyx
» Hey Guys
Wed Oct 21, 2015 8:25 pm by Onyx
» WOT Tuning Basics
Mon Oct 19, 2015 12:08 pm by AJracer33a
» new to the forum/me member on fb
Sat Oct 10, 2015 12:52 pm by AJracer33a
» DSM beginner
Sat Oct 10, 2015 12:51 pm by AJracer33a
» 4G37 Timing Belt Install Gone Wrong
Fri Feb 13, 2015 2:02 am by SafetyAl
» '93 7 Bolt 4G63T
Sat Jan 31, 2015 9:04 pm by crazyccustoms666
» My DSM History
Wed Jan 28, 2015 10:25 pm by pointblank9957